Product Advantage
Asymmetric Structural Efficiency: The 30mm×60mm asymmetric cross-section optimizes load distribution— the 60mm-wide side provides a tensile strength of ≥210MPa and a bending strength of ≥180MPa, suitable for bearing vertical loads (e.g., sliding door weights up to 80kg), while the 30mm-narrow side saves installation space, fitting into tight gaps as small as 35mm.
Superior Corrosion & Wear Resistance: The surface undergoes professional treatment—10-15μm thick anodizing creates a dense oxide film that withstands 1000 hours of neutral salt spray testing without rusting, while optional wear-resistant powder coating (60-80μm) reduces friction, extending service life by 50% in high-frequency use scenarios (e.g., sliding door tracks).
Precision Dimensional Control: Adopting CNC extrusion molds and post-production calibration, the profile achieves a dimensional tolerance of ±0.08mm. This ensures seamless assembly with matching components (e.g., sliding rollers, connectors), eliminating gaps that cause noise or structural instability.
Multi-Scenario Customization: Supports length customization (1m-6m) and surface finish personalization—anodized silver for industrial aesthetics, black powder coating for modern interiors, and wood grain transfer for home decor. It also accepts on-demand drilling, slotting, and chamfering to match specific design blueprints.
Eco-Friendly & Cost-Effective: Made of 100% recyclable 6063 aluminum alloy, it aligns with global green building goals (e.g., LEED). Its lightweight property (density 2.7g/cm³) reduces transportation costs by 30% compared to steel profiles, and its low maintenance needs cut long-term operational expenses.
Technical Parameters
Parameter | Specification | Unit | Test Standard |
Material | 6063-T5 Aluminum Alloy | - | ASTM B221 |
Cross-Sectional Size | 30×60 | mm | GB/T 6892 |
Tensile Strength | ≥210 | MPa | ASTM B557 |
Yield Strength | ≥170 | MPa | ASTM B557 |
Elongation Rate (50mm) | ≥8 | % | ASTM B557 |
Thermal Conductivity | 201 | W/(m·K) | ASTM E1461 |
Surface Finish | Anodizing (10-15μm), Powder Coating (60-80μm), Wood Grain Transfer | - | ASTM B928 |
Density | 2.7 | g/cm³ | ASTM B328 |
Maximum Operating Temperature | -50 ~ 120 | ℃ | GB/T 3194 |
Standard Length (Customizable) | 6000 (1000-6000) | mm | Customer Requirement |
Straightness Tolerance | ≤0.5 | mm/m | GB/T 6892 |
Wear Resistance (Powder Coated) | ≤0.01g/1000 cycles | g/cycle | ASTM D4060 |
Product Uses
1. Residential Sliding Door Systems: Used as upper and lower tracks for wardrobe sliding doors, balcony glass doors, and room dividers. The 60mm-wide side provides stable load-bearing for door panels (up to 80kg), while the 30mm-narrow side fits into wall recesses, avoiding protrusions that occupy living space.
2. Industrial Equipment Frames: Assembled into lightweight brackets for conveyor belts, automated assembly line guards, and testing equipment bases. Its asymmetric design allows it to attach to both vertical and horizontal surfaces, simplifying the integration of sensors and control panels.
3. Commercial Display Fixtures: Built into shelf supports and display stand frames for retail stores (e.g., clothing shops, electronics malls). The customizable surface finish (e.g., brushed anodizing) enhances product visibility, while the profile’s strength ensures it can hold display items weighing up to 30kg per meter.
4. Architectural Interior Trim: Applied as ceiling keels for suspended ceilings and wall edge trims in offices and hotels. The 30mm-narrow side fits neatly against walls, creating a seamless transition between surfaces, and the corrosion-resistant finish maintains a clean appearance in high-traffic areas.
Product Operate Guide
Pre-Installation Preparation: Verify that the profile’s cross-section, length, and surface finish match the design. Clean the surface with a lint-free cloth to remove dust or oil—avoid using abrasive cleaners that damage the finish. For outdoor use, prepare waterproof sealant and anti-rust connectors.
Assembly Steps: Use M5-M6 aluminum-specific bolts for connection. When installing sliding door tracks, ensure the 60mm-wide side is facing upward (for load-bearing) and use a level to calibrate straightness (tolerance ≤0.3mm/m). For drilling, use a high-speed steel drill bit to prevent profile cracking.
Post-Installation Inspection: Check bolt tightness (recommended torque: 7-9N·m) and confirm no deformation or scratches on the surface. For sliding door tracks, test the smoothness of door movement—adjust the profile position if there is friction or noise.
Maintenance Tips: Clean the surface monthly with neutral detergent and water; for powder-coated profiles, avoid prolonged exposure to strong sunlight to prevent fading. If the anodized layer is scratched, touch up with matching aluminum paint.
FAQ
1. Q: Can the T5 30-60 profile be used for outdoor sliding gates (e.g., garden gates)?
A: Yes, but we recommend upgrading to a 15μm-thick anodized finish and using stainless steel connectors. It can bear outdoor gates weighing up to 60kg, and the corrosion-resistant treatment ensures it withstands rain and humidity for over 10 years.
2. Q: What is the lead time for customized lengths (e.g., 4.5m) and wood grain finish?
A: For customized lengths (1m-6m) with standard finishes, lead time is 5-7 working days. For wood grain transfer, it takes 8-10 working days, including sample confirmation to ensure color matching with your design.
3. Q: Does the profile come with pre-slotted tracks for sliding rollers?
A: Yes, we offer pre-slotted options (slot width: 8mm/10mm) for sliding door rollers—free of charge for orders over 300 meters. For small batches, we can provide a slotting template to guide on-site processing.
4. Q: What is the warranty period for this profile?
A: We provide a 10-year warranty for the aluminum material and a 5-year warranty for surface finishes (anodizing/powder coating). If there is corrosion, deformation, or finish peeling caused by product defects, we offer free replacement.
5. Q: How does this T5 30-60 profile differ from the T5 60-60 profile?
A: The T5 30-60 has an asymmetric cross-section, optimized for space-saving and directional load-bearing (e.g., sliding tracks), while the T5 60-60 is symmetric, suitable for uniform load scenarios (e.g., display stands). The 30-60 also fits into narrower installation gaps.
